ATX® cable pull / lat pull option for Power Rack 800 Series

ATX® cable pull / lat pull option for Power Racks 800 Series

Item no.: ATX-CA-PUL-8-

The CA-PUL-8 built-in cable pull / lat pull for the ATX® Power Racks 800 Series is available in two versions.

- with 125 kg plug-in weights -

- with plate load weight slide for holding Ø 30 mm or Ø 50 mm weight plates

The design is extremely space-saving and integrates perfectly into the existing Power Rack without taking up any significant additional space. The overall height of the rack is not exceeded by the pulley attachment.

Training with dumbbells, as well as the attachment and use of other optional accessories, is not impaired or hindered by the cable pull. The only restriction would be the use of weight plate pins for storing weight plates, which cannot be used in conjunction with the plate load version, or can only be used on one side. The use of weight plate pins can also be combined without restriction with the version with insertable weights.

The cable pulley / lat pulldown has excellent running characteristics and offers pulling options from below and above. The weight ratio is always 1:1.

The guide rods of the weight plate pins / weight carriage are made of solid, hard chrome-plated Ø 20 mm piston rods, which cause very little frictional resistance due to their extremely smooth surface.

The upper castor unit is equipped with heavy-duty needle bearings, and the built-in aluminum pulley has ball bearings and a diameter of Ø 140 mm.

The lower castor unit is fitted with plain bearings and also has a Ø 140 mm aluminum pulley with ball bearings.

The return pulley is an aluminum pulley with ball bearings and a diameter of Ø 90 mm.

The plastic-coated steel cables are flexible and stretch-free.

The plug-in weights are made of precision steel plates and are fitted with plastic plain bearings. The KG / LB stickers are color-coded and the pin has a sturdy metal knob and is attached with a spiral cable.

The weight slide for the plate load version is fitted with specially manufactured plastic plain bearings with a reduced contact surface to minimize frictional resistance. The tiller for the weight plates is matt chrome-plated and made of Ø 30 mm solid steel. The effective usable length is 24.5 cm on each side.

Adapters for Ø 50 mm weight plates are optionally available. (Article no.: BB-OA-250-PVC, 2 pieces required)

The weight sled is of course designed for use with Ø 45 cm weight plates.

The weight of the sled is 8.75 kg.

We recommend the use of adjusting rings to secure the weight plates!

The bench (item no.: ATX-PUL-8-SEAT) is optionally available and turns the cable pulley into a fully-fledged lat pull-down device.

The bench is simply clipped into the posts of the rack and secured with a locking bolt. The contact surfaces are fitted with polyamide insulators to protect the powder coating of the racks.

The height of the leg castors can be adjusted in 6 positions and are secured with a clamping locking pin. The adjustment runs gently over polyamide sliding strips and the castor holder is fitted with a safety catch to prevent it being pulled out.

The seat can be attached to the rack in 5 cm increments at any height and can therefore be optimally adjusted for any body size.

The weight of the bench including leg rollers is approx. 13.8 kg.

Suitable for:

The cable pull fits all ATX® Power Racks of the 800 Series.

Please note! A rack extension (article no.: ATX-EXT-800-B / ATX-EXT-800-F) must be fitted to the power rack in order to install the cable pull!

Scope of delivery:

1x upper castor unit

1x lower castor unit

1x deflection roller unit

2x guide rods

2x rubber buffers for plug-in weights / weight slides

2x plastic-coated steel cables including cable clamps and cable protection rosettes

1x extension chain for suspending the optionally available pull handles

3x snap hooks 10 mm

Fastening material

125 kg plug-in weights (optional position)

Weight slide Ø 30 mm (optional position)

The power racks, pull handles, weight plates and Ø 50 mm adapters shown are not included in the scope of delivery!

The bench is optional and must be ordered separately!

Adapter 50 mm x 270 mm plastic

5,90 €

Bench for cable pull option - Power Rack 800 Series

118,00 €

Cable option plate load - Power Rack 800-Series

380,00 €

Cable pull option 125 KG plug-in weights - Power Rack 800-Series

795,00 €

We would be happy to provide you with a quote including shipping costs. Simply ask us using the contact form or call us on 0049 911 521919-10.